BALSA
1	2- 24 X 1/2 X 3/8 stab leading edge
2	2- 24 X 1/1/4 X 5/8 stab trailing edge
3	1- 10 X 1/2 X 1 for stab and elevator tips
4	1- 36 X 1/8 X 2 for wing trailing edge if flaps are used
5	1- 3-1/2 X 1-3/4 X 1-1/2 rudder bottom, (use #8 scrap from
6	1- 24 X 3/8 square for elevator pushrod
7	1- 24 X 3/8 square for rudder pushrod
8	2 - 36 X 1 X 1/2 wing leading edge
9	2 - 36 X 3/4 X 3/8 wing trailing edge
10	2 - 7 X 2 X 1-3/8 for wing tips
11	1 - 5 X 1 X 1 for rear wing dowel reinforcement
12, 13	12 - 36 X 4 X 1/16 sheeting for wings, stab, elevator & rudder
PLYWOOD
14	1- 1/4" Firewall
15	1- Front wing saddle reinforcement plate
16	1- Rear wing saddle reinforcement plate
17	1- 1/8" ply tail wheel bulkhead
18	1- 12" X 4" X 1/8" ply for gear doors
19	2- 1/4" retract mount plates
DOWELS
20	2 - 1-1/2 X 1/4 dowels for rear wing mounts
21	12 - 1/4 X 1 dowels for retract plate anchors,flap and el. horn
22	1- 5" X 1/4" dowel for flap horn bushing, elevator horn bushing bushing and flap servo anchor
HARDWOOD
23	20" 3/8" square pine for radio mount beams
24	2 - 1-1/4 X 3/8 square pine for aileron servo mount beams
25	1- 6" X 3/8" square hardwood for cowl mount screw blocks
26	1- 2" X 1" X 1" pine block for wing mount blind nut
27	2- 3/4 X 1/4 X 1" pine blocks for gear door hinge mounts
28	4- 1 X 3/4 X 1/2 pine for flaps and gear door servo mounts
HARDWARE
29	1- 22" X 3" fiberglass cloth for wing joint reinforcement
30	2- 1/8" X 2" ID brass tubes for flap horns
31	2- 5" X 1/8" steel rod for flap horns
32	1- control arm for rudder
33	18- hinges for ailerons, rudder, gear doors
34	2 - 1" X 3/32" ID brass tubes for elevator coupler bushing
35	1- 5" X 3/32" steel rod for elevator coupler
36	1- Sheet metal elevator horn
37	1- 3-1/2" P51 spinner
38	1- Retractable tail wheel
39	1- 3" X 1/4" NC nylon wing bolt and blind nut
40	1- hardware pac.3 aluminum horns,1 nylon horn,18 hngs,12 clevices
41	1- set of full size plans
42	1- set of stars and bars decals
43	6- 12 2-56 X 3/4 machine screws for nyrod ends
44	1- 2-56 X 1" machine screw for aileron nyrod connector
45	1- 3" X 1/16" wire for aileron connector
46	1- 60" piece of nylon line for tail wheel doors
47	8- #4 X 3/4" screws for mounting retracts
48	1- 4" X 1/16" wire for flap pushrod
49	1- 12"X 1/8" wire for flap pushrod
50	2 - sheet metal plates for flap pushrods
51	2 - aluminum aileron control horns
52	13- #4 X 3/8" sheetmetal screws for mounting the cowl,tail wheel gear and servo mount cross rails
53	2- 1/4" X 3/4" sheet metal for gear door arm plates
54	1- Foam rudder core
P-51 ACCESSORIES (not supplied with the kit)
1	1 .50-.91 size 2 cycle engine
2	2 3-1/2" military style wheels for the main gear
3	1 1-1/4" tail wheel
4	1 12-16 oz. fuel tank
5	1 motor mount to fit your size engine
6	1 7 channel radio and 7 servos
7	1 #104 Spring Air 2 gear retractable landing gear set (85) ( 90 ) degree will work also)
8	1 pair of Robostruts from Robart Manufacturing
9	2 5/32" wheel collars
10	1 1/16" wheel collar
11	1 Roll of Monokote and paint for your color scheme
12	1 1/7 scale WW II military scale pilot